国网江西省电力有限公司电力科学研究院,江西 南昌 330096
汤锦慧(1991—),女,硕士,高级工程师,研究方向为电网化学与环保,E-mail:15070991755@163.com。
收稿:2025-11-19,
修回:2026-01-14,
纸质出版:2026-06-28
移动端阅览
汤锦慧, 伍发元, 王震, 等. 预氧化调控无烟煤衍生硬碳结构及其储钠性能[J]. 储能科学与技术, 2026, 15(6): 2104-2117.
TANG Jinhui, WU Fayuan, WANG Zhen, et al. Pre-oxidation modulated structure of anthra-derived hard carbon for enhanced sodium storage performance[J]. Energy Storage Science and Technology, 2026, 15(6): 2104-2117.
汤锦慧, 伍发元, 王震, 等. 预氧化调控无烟煤衍生硬碳结构及其储钠性能[J]. 储能科学与技术, 2026, 15(6): 2104-2117. DOI: 10.19799/j.cnki.2095-4239.2025.1048.
TANG Jinhui, WU Fayuan, WANG Zhen, et al. Pre-oxidation modulated structure of anthra-derived hard carbon for enhanced sodium storage performance[J]. Energy Storage Science and Technology, 2026, 15(6): 2104-2117. DOI: 10.19799/j.cnki.2095-4239.2025.1048.
无烟煤作为钠离子电池硬碳负极的前驱体,具有碳含量高和成本低的优势,但其直接碳化易石墨化,层间距过小,限制了储钠能力。为此,本研究系统对比了多种预氧化方法,筛选出最优的混酸(硫酸/硝酸)氧化策略,在预氧化温度70℃反应9 h条件下,实现了对类石墨微区结构的有效调控。硫酸作为磺化剂和插层介质,引入磺酸基团,有效打破无烟煤的致密芳香结构并扩大碳层间距,硝酸则作为强氧化剂,通过引入含氮/氧官能团促进芳香片层间的交联,抑制高温石墨化趋势,并协同构建丰富的超微孔与闭孔结构。改性后的无烟煤衍生硬碳材料在0.02 A/g电流密度下可逆容量达321.15 mAh/g,平台容量提升至210.7 mAh/g,即使在2.0 A/g高倍率下仍可保持207.3 mAh/g的可逆容量。选择最佳硬碳材料研究其储钠机制,通过循环伏安、恒电流间歇滴定(GITT)等测试,可以推测低电位区(0.01~0.1 V)的容量贡献主要源于钠离子在闭孔中的填充和在层间的嵌入行为,验证了“吸附-嵌入/填充”的储钠机制。本研究从分子层面实现了对硬碳前驱体结构的精准调控,为低成本、高性能硬碳负极的开发提供了新思路。
Anthracite is considered to be a promising precursor for hard carbon anodes in sodium-ion batteries (SIBs)
primarily due to its naturally high fixed-carbon content
structural stability
and low cost. However
the direct carbonization of anthracite tends to induce excessive graphitization
which results in insufficient interlayer spacing (d002) and consequently leads to limited sodium-storage capacity. In particular
it diminishes the plateau capacity in the low-potential region that is critical for achieving high e
nergy density in SIBs. To overcome these structural limitations
in this work we systematically investigated and compared multiple pre-oxidation strategies—including air oxidation
single-acid treatments
and mixed-acid oxidation—aimed at modifying the microstructure of anthracite before carbonization. We identified a mixed-acid oxidation method using sulfuric acid (H
2
SO
4
) and nitric acid (HNO
3
) as the most effective one. Under optimized conditions of 70℃ for 9 hours
this method successfully modulates the graphite-like microdomains in the carbon precursor. In this process
sulfuric acid acts as a sulfonating and intercalating agent
introducing sulfonic groups (—SO
3
H) that help break the dense aromatic structure of anthracite and expand the interlayer spacing. Nitric acid serves as a strong oxidant
incorporating nitrogen- and oxygen-containing functional groups that promote cross-linking between aromatic layers
thereby suppressing graphitization during high-temperature treatment. The synergistic effect of both acids also facilitates the formation of abundant ultramicropores and closed pores. The optimized hard carbon material exhibits significantly improved electrochemical performance. It delivers a reversible capacity of 321.15 mAh/g at 0.02 A/g
with a plateau capacity of 210.7 mAh/g. Even at the high current density of 2.0 A/g
it maintains a capacity of 207.3 mAh/g
demonstrating excellent rate capability. To investigate the sodium-storage mechanism of the best-performing sample
we employed cyclic voltammetry and a galvanostatic intermittent-titration technique. The results suggest that the capacity in the low-potential region (0.01-0.1 V) arises mainly from sodium-ion insertion into the expanded interlayers and filling into closed pores
supporting a combined "adsorption-intercalation/filling" mechanism. In summary
this study demonstrates a rational and effective pre-oxidation strategy for achieving molecular-level structural tailoring of anthracite-derived ha
rd carbon. The proposed mixed-acid treatment not only enhances the interlayer spacing and introduces beneficial functional groups but also creates a favorable pore structure for sodium storage. These findings offer valuable new insights into the design of low-cost
high-performance carbon anodes for SIBs and underscore the importance of precursor engineering in regulating sodium-storage behavior for next-generation energy-storage systems.
CAI X S, YUE Y Y, YI Z, et al. Challenges and industrial perspectives on the development of sodium ion batteries[J]. Nano Energy, 2024, 129: 110052. DOI:10.1016/j.nanoen. 2024.110052.
CHEN J W, ADIT G, LI L, et al. Optimization strategies toward functional sodium-ion batteries[J]. Energy & Environmental Materials, 2023, 6(4): e12633. DOI:10.1002/eem2.12633.
DELMAS C. Sodium and sodium-ion batteries: 50 years of research[J]. Advanced Energy Materials, 2018, 8(17): 1703137. DOI:10.1002/aenm.201703137.
PHOGAT P, RAWAT S, DEY S, et al. Advancements and challenges in sodium-ion batteries: A comprehensive review of materials, mechanisms, and future directions for sustainable energy storage[J]. Journal of Alloys and Compounds, 2025, 1020: 179544. DOI:10.1016/j.jallcom.2025.179544.
JIA K K, ZHU L N, WU F. Phenylpyridine dicarboxylate as highly efficient organic anode for Na-ion batteries[J]. ChemSusChem, 2021, 14(15): 3124-3130. DOI:10.1002/cssc.202100872.
YIN B, HE H Y, LIN J D, et al. Bichannel design inspired by membrane pump: A rate booster for the conversion-type anode of sodium-ion battery[J]. Journal of Materials Chemistry A, 2022, 10(7): 3373-3381.
OPRA D P, ZHELEZNOV V V, SINEBRYUKHOV S L, et al. Copper-doped sodium titanate with a hierarchical micro/nano structure as an anode material for Na-ion batteries[J]. Journal of Power Sources, 2024, 600: 234230. DOI:10.1016/j.jpowsour. 2024.234230.
YUAN Y T, JAN S, WANG Z Y, et al. A simple synthesis of nanoporous Sb/C with high Sb content and dispersity as an advanced anode for sodium ion batteries[J]. Journal of Materials Chemistry A, 2018, 6(14): 5555-5559.
XIAO M J, DAI X H, JIANG Y. Recent advances modification of hard carbon materials and its application in sodium ion batteries[J]. Journal of Energy Storage, 2025, 111: 115411. DOI:10.1016/j.est.2025.115411.
MAHATO S, DAS A, BISWAS K. Experimental and theoretical investigation on boron, phosphorus dual doped hard carbon as anode for sodium-ion battery[J]. Journal of Energy Storage, 2024, 104: 114422. DOI:10.1016/j.est.2024.114422.
SCHUTJAJEW K, GIUSTO P, HÄRK E, et al. Preparation of hard carbon/carbon nitride nanocomposites by chemical vapor deposition to reveal the impact of open and closed porosity on sodium storage[J]. Carbon, 2021, 185: 697-708. DOI:10.1016/j.carbon.2021.09.051.
TIAN X R, LUO S H, WANG G, et al. Microstructure and surface chemistry modification strategies of lignite-based hard carbon anode by high temperature carbonization for enhanced sodium ion storage[J]. Journal of Energy Storage, 2025, 113: 115684. DOI:10.1016/j.est.2025.115684.
WANG Q Q, HU Z, ZHANG R S, et al. Anode of anthracite hard carbon hybridized by phenolic epoxy resin toward enhanced performance for sodium-ion batteries[J]. ACS Applied Energy Materials, 2024, 7(15): 6704-6716.
ZHANG X, LI J Y, LIANG H M, et al. Mechanistic study on the effect of acid leaching treatment on the microstructure evolution of different coal species and their macro-oxidative exothermic properties[J]. Thermochimica Acta, 2025, 747: 179975. DOI:10. 1016/j.tca.2025.179975.
ZHONG H, HUANG Q H, ZOU M Y, et al. From food to hard carbon: Citric acid enhanced biomass-derived anodes for high-performance sodium storage[J]. Chemical Engineering Journal, 2025, 508: 160879. DOI:10.1016/j.cej.2025.160879.
CHEN X Y, LIU C Y, FANG Y J, et al. Understanding of the sodium storage mechanism in hard carbon anodes[J]. Carbon Energy, 2022, 4(6): 1133-1150. DOI:10.1002/cey2.196.
CHEN W M, CHEN C J, XIONG X Q, et al. Coordination of surface-induced reaction and intercalation: Toward a high-performance carbon anode for sodium-ion batteries[J]. Advanced Science, 2017, 4(6): 1600500. DOI:10.1002/advs.201600500.
TANG X H, XIE F, LU Y X, et al. Intrinsic effects of precursor functional groups on the Na storage performance in carbon anodes[J]. Nano Research, 2023, 16(11): 12579-12586. DOI:10. 1007/s12274-023-5643-9.
SHAO Y Y, XIAO J, WANG W, et al. Surface-driven sodium ion energy storage in nanocellular carbon foams[J]. Nano Letters, 2013, 13(8): 3909-3914. DOI:10.1021/nl401995a.
FERRARI A C, BASKO D M. Raman spectroscopy as a versatile tool for studying the properties of graphene[J]. Nature Nanotechnology, 2013, 8(4): 235-246. DOI:10.1038/nnano. 2013.46.
FERRARI A C, ROBERTSON J. Interpretation of Raman spectra of disordered and amorphous carbon[J]. Physical Review B, 2000, 61(20): 14095-14107. DOI:10.1103/physrevb.61.14095.
FERRARI A C. Raman spectroscopy of graphene and graphite: Disorder, electron-phonon coupling, doping and nonadiabatic effects[J]. Solid State Communications, 2007, 143(1/2): 47-57. DOI:10.1016/j.ssc.2007.03.052.
BRAGG W H, BRAGG W L. The reflection of X-rays by crystals[J]. Proceedings of the Royal Society of London Series A, Containing Papers of a Mathematical and Physical Character, 1913, 88(605): 428-438. DOI:10.1098/rspa.1913.0040.
SCHERRER P. Estimation of the size and internal structure of colloidal particles by means of röntgen[J]. Nachr Ges Wiss Göttingen, 1918, 2: 96-100.
BREZESINSKI T, WANG J, TOLBERT S H, et al. Ordered mesoporous α-MoO 3 with iso-oriented nanocrystalline walls for thin-film pseudocapacitors[J ] . Nature Materials, 2010, 9(2): 146-151. DOI:10.1038/nmat2612.
CHEN X Y, TIAN J Y, LI P, et al. An overall understanding of sodium storage behaviors in hard carbons by an "adsorption-intercalation/filling" hybrid mechanism[J]. Advanced Energy Materials, 2022, 12(24): 2200886. DOI:10.1002/aenm.202200886.
SONG M X, YI Z L, XU R, et al. Towards enhanced sodium storage of hard carbon anodes: Regulating the oxygen content in precursor by low-temperature hydrogen reduction[J]. Energy Storage Materials, 2022, 51: 620-629. DOI:10.1016/j.ensm. 2022.07.005.
JIANG M W, HOU Z D, WANG J J, et al. Balanced coordination enables low-defect Prussian blue for superfast and ultrastable sodium energy storage[J]. Nano Energy, 2022, 102: 107708. DOI:10.1016/j.nanoen.2022.107708.
ZHAO Y H, HU Z, ZHOU W, et al. Advanced structural engineering design for tailored microporous structure via adjustable graphite sheet angle to enhance sodium-ion storage in anthracite-based carbon anode[J ] . Advanced Functional Materials, 2024, 34(44): 2405174. DOI:10.1002/adfm.202405174.
ZHAO G X, XU T Q, ZHAO Y M, et al. Conversion of aliphatic structure-rich coal maceral into high-capacity hard carbons for sodium-ion batteries[J]. Energy Storage Materials, 2024, 67: 103282. DOI:10.1016/j.ensm.2024.103282.
LI R, SU C B, YANG W, et al. Molecular level modulation of anthracite-based hard carbon precursors for efficient sodium-ion batteries[J]. Chemical Engineering Journal, 2025, 506: 159968. DOI:10.1016/j.cej.2025.159968.
WANG K F, SUN F, WANG H, et al. Altering thermal transformation pathway to create closed pores in coal-derived hard carbon and boosting of Na + plateau storage for high-performance sodium-ion battery and sodium-ion capacitor[J ] . Advanced Functional Materials, 2022, 32(34): 2203725. DOI:10.100 2/adfm.202203725.
LI R, YANG B R, HU A J, et al. Heteroatom screening and microcrystal regulation of coal-derived hard carbon promises high-performance sodium-ion batteries[J]. Carbon, 2023, 215: 118489. DOI:10.1016/j.carbon.2023.118489.
WANG J, CUI Y L, GU Y, et al. Coal-based modified carbon for high performance sodium-ion battery[J]. Solid State Ionics, 2021, 368: 115701. DOI:10.1016/j.ssi.2021.115701.
0
浏览量
8
下载量
0
CSCD
关联资源
相关文章
相关作者
相关机构
京公网安备11010102001997号