YUAN Bingqing, CHEN Liang, ZHANG Xubao, et al. Design and optimization of multiscale three-dimensional conductive network structures for fast-charging lithium-ion batteries[J]. Energy Storage Science and Technology, 2026, 15(8): 2997-3008.
YUAN Bingqing, CHEN Liang, ZHANG Xubao, et al. Design and optimization of multiscale three-dimensional conductive network structures for fast-charging lithium-ion batteries[J]. Energy Storage Science and Technology, 2026, 15(8): 2997-3008.DOI: 10.19799/j.cnki.2095-4239.2026.0470.
Design and optimization of multiscale three-dimensional conductive network structures for fast-charging lithium-ion batteries
To address the growing demand for fast-charging lithium-ion batteries in electric vehicles
large-scale energy storage systems
and portable electronic devices
and to overcome the sluggish ion transport kinetics
severe polarization
and limited cycle life exhibited by conventional electrodes under high-current operating conditions
this study investigates the design of a multiscale three-dimensional conductive network architecture and its optimization for enhanced ion transport.First
based on characteristic time constant theory
the kinetic relationship between electron conduction and ion diffusion during fast charging is quantitatively analyzed
demonstrating that ion transport becomes the dominant rate-limiting factor at charging rates above 10 C. Accordingly
a design strategy based on dual continuity and kinetic matching of electron and ion transport pathways is proposed. The mechanisms by which the three-dimensional conductive network reduces transport resistance and mitigates polarization by establishing efficient electron-conduction pathways and optimized ion-diffusion channels are systematically elucidated. An evaluation framework centered on the dimensionless structural efficiency factor (
β
=
ε
/
τ
) is established
and a hierarchical collaborative design strategy spanning the micro-
meso-
and macro-scales is developed to identify the optimal structural parameters at each scale. A multiscale
multiphysics numerical model is established using COMSOL Multiphysics 6.0 with clearly defined modeling assumptions and applicability rang
es (porosity 30%—55%; graphene content 2%—5%; charging rate: ≤12 C). Multi-objective optimization using response surface methodology enables precise matching between structural parameters and transport performance. The electrodes are fabricated using an integrated process combining three-dimensional printing
in situ
sintering
and dispersion techniques
achieving a production rate of 50 electrodes per hour and a material utilization efficiency exceeding 95%
thereby demonstrating strong potential for scalable manufacturing. Electrochemical characterization shows that the optimized electrode delivers a specific capacity of 138 mAh/g at a high charging rate of 10 C
with a coulombic efficiency of 94.5% and a capacity retention of 91.3% after 1000 charge-discharge cycles. The optimized architecture increases the lithium-ion diffusion coefficient to 1.2×10
-11
cm
2
/s and reduces the charge-transfer resistance to 75 Ω·cm
2
. Additionally
the electrode maintains excellent electrochemical performance over a wide operating temperature range
from -20℃ to 55℃. Finally
the broader applicability of the proposed multiscale design strategy is discussed for silicon anodes
sulfur cathodes
and composite solid-state electrolyte electrodes. Remaining challenges
including the long-term stability of ZrO
2
coating layers and interfacial fatigue mechanisms
are also identified. These findings provide valuable theoretical guidance and practical support for the industrial development of high-rate
SHAN Y H, LI L B, DU J T, et al. High performance lithium-sulfur batteries using three-dimensional hierarchical porous carbons to host the sulfur[J]. New Carbon Materials, 2021(6): 1094-1102.
ZHAO Y B, YANG T L, ZHAO G J, et al. Progress of fast charging technology for lithium-ion battery[J]. Chinese Journal of Power Sources, 2021, 45(9): 1219-1222.
GUAN Y B, SHEN J R, LI K L, et al. Application of graphene conductive additives in cathodes of lithium ion batteries[J]. Energy Storage Science and Technology, 2020, 9(1): 70-81. DOI: 10.12028/j.issn.2095-4239.2019.0175.
YANG B W, WANG R, XIN B J, et al. C-SnO 2 /MWCNTs composite with stable conductive network for lithiumbased semi-solid flow batteries[J ] . Acta Physico-Chimica Sinica, 2025, 41(2): 98-106.
ZHANG S Z, CHEN Y J, LI H, et al. Co 3 O 4 -GN-CNT network derived from ZIF-8@ZIF-67 as high-performance lithium-ion battery anode material[J ] . Journal of Functional Materials, 2024, 55(2): 2015-2021. DOI: 10.3969/j.issn.1001-9731.2024.02.003.
ZENG R L, GOU Q Y, ZHANG B Y, et al. Germanium oxide-based anode materials for lithium-ion batteries[J]. The Chinese Journal of Nonferrous Metals, 2025, 35(9): 3069-3089.
ZOU C, GU H T, FENG Z H, et al. High-efficiency fabrication and electrochemical property of Si/NiSi 2 @ C composite anode materials for Li-ion batteries[J ] . Journal of Materials Science and Engineering, 2019, 37(1): 22-29. DOI: 10.14136/j.cnki.issn1673-2812.2019.01.005.
WANG M, ZENG Y H, HE Y, et al. Preparation and lithium storage properties of silicon/reduced graphene oxide nanocomposites[J]. Journal of the Chinese Ceramic Society, 2023, 51(7): 1689-1696. DOI: 10.14062/j.issn.0454-5648.2022 1016.
LI Y L, YU D D, LIN S, et al. Preparation of α-MnO 2 nanorods/porous carbon cathode for aqueous zinc-ion batteries[J ] . Acta Chimica Sinica, 2021, 79(2): 200-207.